Category: BULK PLA+

Bulk PLA+ reels and outer units

Showing all 12 results

10x eSun Black PLA+ 1.75mm
Original price was: $299.90.Current price is: $293.90.
10kg - Black
10x eSun Black PLA+ Filament 1.75mm – comes as an outer unit of 10 vacuum packed 1KG rolls.
Add to cart Details Buy Now
10x eSun Cold White PLA+ 1.75mm
Original price was: $299.90.Current price is: $293.90.
10kg - Cold White
10x eSun Cold White PLA+ Filament 1.75mm – comes as an outer unit of 10 vacuum packed 1KG rolls.
Add to cart Details Buy Now
10x eSun Grey PLA+ 1.75mm
Original price was: $299.90.Current price is: $293.90.
10kg - Grey
10x eSun Grey PLA+ Filament 1.75mm – comes as an outer unit of 10 vacuum packed 1KG rolls.
Add to cart Details Buy Now
10x eSun Silver PLA+ 1.75mm
$316.90
10kg - Silver
10x eSun Silver PLA+ Filament 1.75mm – comes as an outer unit of 10 vacuum packed 1KG rolls.
Add to cart Details Buy Now
10x eSun White PLA+ 1.75mm
Original price was: $299.90.Current price is: $293.90.
10kg - White
10x eSun White PLA+ Filament 1.75mm – comes as an outer unit of 10 vacuum packed 1KG rolls.
Add to cart Details Buy Now
Out of Stock
Sold Out

eSun Black 3kg Bulk PLA+ 1.75mm
$88.00
3kg - Black Bulk
eSun Black PLA+ Filament 1.75mm – comes on a vacuum packed 3KG roll
Read more Details

eSun Grey 3kg Bulk PLA+ 1.75mm
$88.00
3kg - Grey Bulk
eSun Grey Bulk PLA+ Filament 1.75mm – comes on a vacuum packed 3KG roll
Add to cart Details Buy Now

eSun PLA+ 10x 1Kg – Mixed
Original price was: $300.00.Current price is: $293.90.
10 rolls mixed colour eSun PLA+ – stated price is for 10x1kg
Select options Details

eSun PLA+ 6x 1Kg – Mixed
Original price was: $180.00.Current price is: $172.90.
6 rolls mixed colour eSun PLA+ – stated price is for 10x1kg
Select options Details

eSun Red 3kg Bulk Roll PLA+ 1.75mm
$88.00
3kg - Red
eSun Red Bulk PLA+ Filament 1.75mm – comes on a vacuum packed 3KG roll
Add to cart Details Buy Now

eSun Silver 3kg Bulk Roll PLA+ 1.75mm
$88.00
3kg - Silver Bulk
eSun Silver Bulk PLA+ Filament 1.75mm – comes on a vacuum packed 3KG roll
Add to cart Details Buy Now

eSun White 3kg Bulk PLA+ 1.75mm
$88.00
Rated 5.00 out of 5
3kg - White Bulk
eSun White Bulk PLA+ Filament 1.75mm – comes on a vacuum packed 3KG roll
Add to cart Details Buy Now

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Andrew Jackson

5

I was directed to 3D... Read More
I was directed to 3DEA by a work colleague as I was new to 3D printing and they were right about them. Great quality PLA (and many other types), awesome range of colours and great pricing. I've bought 4 different rolls so far and they have all been great, no clogging and brilliant print quality. Read Less

Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!

Category: BULK PLA+

10x eSun Black PLA+ 1.75mm

10x eSun Cold White PLA+ 1.75mm

10x eSun Grey PLA+ 1.75mm

10x eSun Silver PLA+ 1.75mm

10x eSun White PLA+ 1.75mm

eSun Black 3kg Bulk PLA+ 1.75mm

eSun Grey 3kg Bulk PLA+ 1.75mm

eSun PLA+ 10x 1Kg – Mixed

eSun PLA+ 6x 1Kg – Mixed

eSun Red 3kg Bulk Roll PLA+ 1.75mm

eSun Silver 3kg Bulk Roll PLA+ 1.75mm

eSun White 3kg Bulk PLA+ 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA