Category: HIPS

Name: 3DEA
Address: Keith Hay Court, Silverdale, Auckland, 0932
Rating: 4.7

Showing all 6 results

Quick View

HIPS – Black 1.75mm
$25.90
1kg - Black
Black quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll.
Add to cart Details Buy Now
Quick View

HIPS – Blue 1.75mm
$25.90
1kg - Blue
Standard Blue quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll.
Add to cart Details Buy Now
Quick View

HIPS – Green 1.75mm
$25.90
1kg - Green
Standard Green quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll.
Add to cart Details Buy Now
Quick View

HIPS – Pink 1.75mm
$25.90
1kg - Pink
Pink quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll.
Add to cart Details Buy Now
Quick View

HIPS – Red 1.75mm
$25.90
1kg - Red
Red quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll.
Add to cart Details Buy Now
Quick View

HIPS – White/Natural 1.75mm
$25.90
1kg - White/Natural
Standard Natural/White quality 1.75mm HIPS Filament – comes on a vacuum packed 1KG Roll. This product is the raw material with no colour pigments.
Add to cart Details Buy Now

Blair Hammond

5

Ive been buying most... Read More
Ive been buying most of my filament from 3DEA for years now. I can't think of a single time I've been let down. Wide selection that's very very rarely out of stock, and their "house Brand" is nicely priced and prints bloody good. Read Less
Sam Willis

5

Outstanding advice a... Read More
Outstanding advice and service. One conversation and a simple order with them, and we finally have our SunluS9 printer up and running again after weeks of troubleshooting. 10/10 Read Less
Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Write a review!

Category: HIPS

HIPS – Black 1.75mm

HIPS – Blue 1.75mm

HIPS – Green 1.75mm

HIPS – Pink 1.75mm

HIPS – Red 1.75mm

HIPS – White/Natural 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA