Tag: Composite PLA

Showing all 7 results

Quick View

eSun ePLA-CF PLA-Carbon Fibre Composite1.75mm
Original price was: $53.90.Current price is: $45.00.
1kg - Black, Brown, Green, Purple, Red
eSUN’s ePLA-CF is a high-quality PLA filament reinforced with organically impregnated, short-cut carbon fibres for greater strength.
Select options This product has multiple variants. The options may be chosen on the product page Details
Quick View

eSun ePLA-GF PLA-Glass Fibre Composite1.75mm
$49.90
1kg - Natural/Off-White
eSUN’s ePLA-GF is a high-quality PLA filament reinforced with glass fibres for greater strength.
Add to cart Details Buy Now
Out of Stock
Sold Out
Quick View

PLA – Metal Composite Aluminium 1.75mm
$49.90
0.5kg - Metal Composite Aluminium
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Read more Details

Quick View

PLA – Metal Composite Brass 1.75mm
$49.90
0.5kg - Metal Composite Brass
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Bronze 1.75mm
$49.90
0.5kg - Metal Composite Bronze
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Copper 1.75mm
$49.90
0.5kg - Metal Composite Copper
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Red copper 1.75mm
$49.90
0.5kg - Metal Composite Red copper
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

GLEN20

5

3dea is a real pleas... Read More
3dea is a real pleasure to deal with. Not only do they stock a great range of filament which you can get from other suppliers in NZ. They have a massive range of own-brand filament which is often unique to NZ and is of the highest quality. All in all, 3dea are highly recommended. Read Less

Write a review!

Tag: Composite PLA

eSun ePLA-CF PLA-Carbon Fibre Composite1.75mm

eSun ePLA-GF PLA-Glass Fibre Composite1.75mm

PLA – Metal Composite Aluminium 1.75mm

PLA – Metal Composite Brass 1.75mm

PLA – Metal Composite Bronze 1.75mm

PLA – Metal Composite Copper 1.75mm

PLA – Metal Composite Red copper 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA