Tag: metal

Showing all 5 results

Out of Stock
Sold Out
Quick View

PLA – Metal Composite Aluminium 1.75mm
$49.90
0.5kg - Metal Composite Aluminium
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Read more Details

Quick View

PLA – Metal Composite Brass 1.75mm
$49.90
0.5kg - Metal Composite Brass
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Bronze 1.75mm
$49.90
0.5kg - Metal Composite Bronze
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Copper 1.75mm
$49.90
0.5kg - Metal Composite Copper
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Quick View

PLA – Metal Composite Red copper 1.75mm
$49.90
0.5kg - Metal Composite Red copper
Composite PLA Metal Filament 1.75mm available in bronze, brass, aluminium, copper and red copper on a 0.5kg roll
Add to cart Details Buy Now

Blair Hammond

5

Ive been buying most... Read More
Ive been buying most of my filament from 3DEA for years now. I can't think of a single time I've been let down. Wide selection that's very very rarely out of stock, and their "house Brand" is nicely priced and prints bloody good. Read Less

Sam Willis

5

Outstanding advice a... Read More
Outstanding advice and service. One conversation and a simple order with them, and we finally have our SunluS9 printer up and running again after weeks of troubleshooting. 10/10 Read Less

Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Write a review!

Tag: metal

PLA – Metal Composite Aluminium 1.75mm

PLA – Metal Composite Brass 1.75mm

PLA – Metal Composite Bronze 1.75mm

PLA – Metal Composite Copper 1.75mm

PLA – Metal Composite Red copper 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA