eSun ASA+ Filament 1.75mm

$48.90

eSun ASA+ quality 1.75mm Filament – comes on a vacuum packed 1KG Roll.

1kg - Warm White, Black, Cold White, Grey

eSun ASA+ Filament exhibits properties comparable to ABS while delivering superior ultraviolet and weather resistance. This advanced filament features exceptional toughness, rigidity, and impact resistance characteristics. Its outstanding weatherability and mechanical attributes provide enhanced protection against environmental degradation, making it the optimal choice for outdoor applications where longevity under exposure conditions is critical.

Diameter 1.75mm2 ±0.03
Density 1.06 ±0.05g/cm2
Print Temp 250-280ºC
Print Speed <250mm/s
Hot bed 90-110ºC (required)
Surface Kapton tape, PET Sheets, ABS/ASA Slurry

A slurry of ABS or ASA and acetone on top of a heated build plate will give an excellent film onto which your parts can adhere.
ASA can be smoothed using controlled exposure to acetone vapours (a process called “vapour smoothing”).
HIPS can be used as a great dissolvable support material for ASA prints. Consider using the Dense Supports option in Simplify3D for best results.

Excellent Weather Resistance

eSUN ASA+ filament exhibits excellent weather resistance and mechanical properties, making it more durable against environmental ageing and suitable for long-term outdoor use, such as in building materials or car accessories.

High Impact Resistance and Mechanical Properties

With ABS-like Properties, eSUN ASA+ filament has higher toughness, rigidity and impact resistance for functional applications. Especially excellent performance in harsh weather conditions and anti-UV.

Clog-free & Bubble-Free & Less-tangle

Full mechanical winding and strict manual examination ensure tangling free and avoid filament breaking and brittle. eSUN ASA+ filament is orderly wrapped, melt well, feed smoothly and constantly without clogging the nozzle or extruder. It does not overlap or tangle, no cracking. High successful printing rate.

Stable Dimensional Tolerance

Minimum tolerance and low warping to ensure consistent feeding and stable prints, good layer bonding, less stringing, no bubbles, easy handling, resulting in an outstanding surface finish and are highly precise.

Vacuumed Sealed Packaging

Filament Net Weight: 1KG. eSUN Filament comes in a sealed vacuum bag with a desiccant bag, easily keep your 3D printer filaments at an optimal storage condition and free from dust or dirt before opening the vacuumed sealed packaging.

Tip

The shrinkage rate of ASA+ is relatively high, so please pay attention to keep constant environmental temperature preservation. When printing, you’d better print it in a constant temperature protective 3D Printer cover.

Weight	1 kg
Dimensions	21 × 21 × 7 cm
Brand	eSun
Colour	Warm White, Black, Cold White, Grey

Brendan

5

13 March 2024 - Revi... Read More

13 March 2024 - Review for: PETG-CF – Carbon Fibre Enhanced PETG Filament Interesting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan. I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove! Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use. My suggestion - get PETG printing well, before moving onto this filament. My printing factors currently: Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/s REVIEW FOR ASA Blue-Grey Printed the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield. Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layers Note: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube. My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel. You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts. Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish. Next step is try printing in an enclosure and to try Acetone smoothing :) NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less
Greedo Twerp

5

I was looking for a ... Read More

I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less
GLEN20

5

3dea is a real pleas... Read More

3dea is a real pleasure to deal with. Not only do they stock a great range of filament which you can get from other suppliers in NZ. They have a massive range of own-brand filament which is often unique to NZ and is of the highest quality. All in all, 3dea are highly recommended. Read Less

Write a review!

eSun ASA+ Filament 1.75mm

ASA – Pink 1.75mm

ASA – White 1.75mm

ASA – Green Fluorescent 1.75mm

PolyLite™ ASA Army Brown 1.75mm

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA

eSun ASA+ Filament 1.75mm

Related products

ASA – Pink 1.75mm

ASA – White 1.75mm

ASA – Green Fluorescent 1.75mm

PolyLite™ ASA Army Brown 1.75mm