HTPLA – Midnight Multicolor
$49.90
Protopasta Midnight HT PLA 3D Printer Filament 1.75mm 500g Multicolor Translucent Transition Glitter Filament; 3D Printing Filament on Recyclable Cardboard Spool.
0.5kg - Midnight
In stock
Inspired by the night sky, Midnight shifts from translucent black to blue w/ grays & blue-grays plus a touch of silver glitter.
Community – Made by Protoplant, Proto-pasta filaments result from individual exploration & having fun w/ friends. Often inspired by or designed in collaboration w/ the community. Enjoy & share!
Creativity – Premium composites & colors, function or form, Protopasta is both technical & creative. Born at the intersection of art & engineering, Protopasta is performance & beauty all-in-one.
Quality – Made from scratch in the USA by Protoplant since 2013 using prime & recycled ingredients. Engineered for consistent diameter, chemistry, & color. Recycle spools to minimize waste.
Reliability – Engineers, artists, designers, & businesses depend on Protopasta, but 3D printing can be challenging even w/ good material. Don’t give up! We’re here for you. Message us for help.
Specs
Semi crystalline, heat treatable PLA for high temp use
Density: 1.24 g/cc
Length: 346 m/kg (1.75) 130 m/kg (2.85)
Typical Printing Temp: 205-225 C
Glass Transition (Tg)*: 60 C
Peak Crystallization (Tc)**: 95-115 C
Onset to Melt (Tm)***: 155 C
Typical change when heat treated: -2% x/y +1% z
Link to Safety Data Page
*max use with no heat treat & max platform temp
**heat treating @ temp 10+ min depending on size/mass
***max use when heat treated (annealed or crystallized)
HTPLA prints well at 205-225 C, however it’s important to match temp to your hardware & volume flow rate. With a typical hotend, you should be able to print at 205 C without jamming at a low flow rate. In machines with hardware that tends towards jamming, consider this video with Joel Telling.
Lower volume flows require lower temps, while higher volume flows require higher temps. In the previously-mentioned video, one way to overcome jamming is to set your temp to a higher-than-typical 240 C. This should then be matched with a high flow rate for a quality printing result.
For direct drives with a short distance between drive gears & nozzle, volume flows can approach 7-8 cubic mm/s or more if printing hot to overcome jamming. For bowden tubes where the distance between drive gear & nozzle are great or less powerful hotends, as little as 2 and as much as 4 cubic mm/s may be the limit. Beware of unintended speed changes from faster infills & slowing down for outlines or short layers. Consider our Ultimaker-specific blog for more on this topic.
A constant speed throughout the part is ideal from an extrusion perspective. Knowing your extrusion width, layer thickness & speed you can calculate your volume flow rate with the calculator like found in the previously-mentioned Ultimaker blog. Alternatively, if you know your volume flow rate limit, extrusion width & layer thickness, you can calculate your speed limit.
Heat Treat
PLA & HTPLA are amorphous in structure as printed (no heat treating) & though both are adequate performers in an office environment, they have poor temperature stability, loosing significant stiffness at temps nearing 60 C. Different than standard PLA, HTPLA is designed to survive heat treating for higher temp stability in a no/minimal load condition to near onset of melting (155 C). That’s an astonishing improvement in thermal stability compared to standard PLA after a quick bake in the oven after printing.
In as little as 5-10 minutes for small, thin parts, HTPLA quickly crystallizes in an oven at 95-115 C (200-240 F) to become more stiff & hold form above glass transition (60 C). Depending on part geometry, setup & technique, parts can deform and shrink. Best results are with flat and/or supported parts with 100% infill. In this instance we experienced x/y shrinkage of about 2% & growth of about 1% in z.
Be sure to avoid hot spots (non-radiating surfaces & no glowing coils) in the oven used for baking & experiment before baking a prized part. Un-printed filament works great for experimentation & translucent makes the transformation most visible! Heat treating is an art, but the resulting improved thermal performance, if needed, is well-worth exploring. You’ll be shocked by the improved thermal stability of your HTPLA parts!!!
High Temperature PLA ( HTPLA )
Looking for increased heat resistance without the need to switch to ABS? Protopasta High Temperature PLA offers heat deflection of up to 88° C (190.4° F) compared to standard PLA of 45-54° C (113-135° F). This makes it a great choice for moving parts (gears, RepRap pieces, etc) or prints that would face moderately high temperatures.
Protopasta High Temperature PLA is made from a mineral filled, impact modified PLA with a nucleating agent to help promote crystallization. Crystallization after printing is what gives this material added heat resistance, so post-print annealing is essential to activate the heat deflection qualities of this material.How do I anneal my print?
You can anneal your finished prints several ways, the two easiest ways are by using hot (but not boiling) water or by placing it in a low temperature oven (newer oven models only). Follow these steps:
- Water Method: Find a pot large enough to hold your print and fill it halfway with water. On medium heat, heat the water until it reaches 95-115 C (200-240 F) (a cooking thermometer works great for this), turn the heat to low and submerge the print in the warm water bath for 6-10 minutes. Placing a lid on your pot will help the water maintain temperature.
- Oven Method: Many newer ovens often have low temperature settings (sometimes called “keep warm” or “bread proof”). Set your oven to 95-115 C (200-240 F), place your finished print on a tray, and set it in the oven for 6-10 minutes.
- SUPPORT YOUR PRINT! Because the annealing process will soften the plastic somewhat, it’s best to support your print during this process.
Because 3D printers vary so much from model to model, and because many RepRap printers combine parts from several manufactures, we can’t provide the optimum temperature for your machine. Generally, our customers find it prints just like standard PLA on their machines (at around 210° C), though others find success running it a bit hotter (around 220° C).Do I need a heated bed? No, High Temp PLA does not require a heated bed or an enclosure.
Weight | 0.5 kg |
---|---|
Dimension | 1.75mm |
Colour | Midnight |
Brand |
Related products
- Add to cart DetailsBuy NowTranslucent PLA is a versatile 3D printer filament that produces semi-transparent prints with a glossy finish. Ideal for creating light-diffusing parts, decorative objects, and visual prototypes.
- Add to cart DetailsBuy Now
With big fleck for maximum texture, Gold Dust Glitter Flake HTPLA has a translucent base with no color added, just big gold flecks. Print thin and let other colors show through or print thick layers and watch layer lines disappear!
- Add to cart DetailsBuy Now
Created from our highest quality, translucent HTPLA v2. A very dynamic and deep color, the blue concentration creates a light blue color that can extend both towards a silvery green and a deep dark purple depending on form and light.
- Add to cart DetailsBuy Now
Take gloss to another level with Glitter Flake HTPLA . Print with the ease of standard PLA with standard hardware and temperatures, but make fun, mesmerizing prints that stand out.
Reviews
There are no reviews yet.