Genuine Phaetus nozzle, hardened steel with DLC coating.

DLC coating on whole nozzle surface with its hardness HV2500, thickness 2μm, and friction coefficient 0.03; Fine finish, low adhesion, high wear resistance.
Superior quality, high temperature and hardness up to HRC62.

Fits any V6 type hotend like: Anycubic i3 Mega, Original Prusa i3 MK2, Original Prusa i3 MK2S, Original Prusa i3 MK2.5, Original Prusa i3 MK3, Original Prusa i3 MK3S, Original Prusa i3 MK2.5S, Anycubic i3 Mega S, Anycubic i3 Mega Zero, Anycubic i3 Mega X, BIQU BX and others

Weight	0.005 kg
Option	1.75/0.4mm, 1.75/0.6mm, 1.75/0.8mm
Brand	Phaetus
Material	Hardened Steel

Reviews

There are no reviews yet.

Be the first to review “DLC Hardened Steel V6 RepRap Phaetus Nozzle”

Blair Hammond

5

Ive been buying most... Read More
Ive been buying most of my filament from 3DEA for years now. I can't think of a single time I've been let down. Wide selection that's very very rarely out of stock, and their "house Brand" is nicely priced and prints bloody good. Read Less
Sam Willis

5

Outstanding advice a... Read More
Outstanding advice and service. One conversation and a simple order with them, and we finally have our SunluS9 printer up and running again after weeks of troubleshooting. 10/10 Read Less
Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less

Write a review!

DLC Hardened Steel V6 RepRap Phaetus Nozzle

Reviews

Revo Brass-Titanium Nozzle Clone

Plated Copper V6 Volcano Hotend Adapter

Phaetus PS EndCoat Hardened Steel V6 RepRap Nozzle

V6 RepRap CHT High-Flow Brass Nozzle Clone

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA

DLC Hardened Steel V6 RepRap Phaetus Nozzle

Reviews

Related products

Revo Brass-Titanium Nozzle Clone

Plated Copper V6 Volcano Hotend Adapter

Phaetus PS EndCoat Hardened Steel V6 RepRap Nozzle

V6 RepRap CHT High-Flow Brass Nozzle Clone