Category: 3D Printer Kits

Showing all 13 results

Quick View

FYSETC Stealthburner PCB Kit with Cables for Voron 2.4 / R2 / Trident (2pcs version)
$69.90

FYSETC Voron 2.4 R2 Trident Stealthburner PCB Kit Standard and 2Pcs PCB boards version Kits with Cables
Add to cart Details Buy Now
Out of Stock
Sold Out

Quick View

LDO Galileo 2 Kit for Clockwork 2 (G2E)
$109.90

One of the most expected project of 2022, the Orbiter v2.0
Read more Details

Quick View

LDO Input Shaper Toolkit
$24.90

The LDO Input Shaper Toolkit comes with all the necessary parts for performing Klipper input shaper calibration with minimal hassle.
Add to cart Details Buy Now

Out of Stock
Sold Out

Quick View

LDO Leviathan V1.2 Control Board
$219.90

Experience the ultimate in 3D Printing control with the LDO Leviathan V1.2 Control Board, featuring an optimized 32 bit controller to provide stable, reliable performance with maximum compatibility.
Read more Details

Quick View

LDO NiteHawk SB Toolboard Kit Rev. C
$129.90

Nitehawk-SB by LDO is a toolboard specifically designed for the Voron Stealthburner toolhead. It is a toolhead PCB featuring RP2040 MCU, TMC2209 stepper drive, ADXL345 accelerometer all integrated into one board.
Add to cart Details Buy Now

Quick View

LDO NiteHawk-36 Toolboard REV C
$129.90

Nitehawk-SB by LDO is a toolboard specifically designed for the Voron Stealthburner toolhead. It is a toolhead PCB featuring RP2040 MCU, TMC2209 stepper drive, ADXL345 accelerometer all integrated into one board.
Add to cart Details Buy Now

Quick View

LDO V1 Z Motor Triple (V1ZMKT3) Teflon Coated for Trident
Price range: $199.90 through $269.90
Rated 5.00 out of 5

High quality stepper motor for the z- axis with integrated lead screw kit for LDO Trident 250/300 Cube or Standard Voron Trident Builds. Kit of 3.
Select options This product has multiple variants. The options may be chosen on the product page Details

clearance

Quick View

PrusaClone i3 MK3S Bear 2.1 Printer Kit
Original price was: $999.90.Current price is: $720.00.

High quality Cloned Prusa i3 MK3S Printer Kit with Bear 2.1 upgraded parts including printed parts.
Add to cart Details Buy Now

Quick View

Quality StealthBurner Extruder Screw Fastener Fans Kit / Voron 2.4 / Trident
$39.90

Quality StealthBurner Extruder Screw Fastener Fans Kit
Add to cart Details Buy Now

Quick View

Voron Printed Parts Kits
Price range: $299.90 through $439.90

Voron Printed Parts Kits are printed to Voron specifications.
Select options This product has multiple variants. The options may be chosen on the product page Details

Quick View

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)
$239.90

This is a complete motor set for the Voron 2.4 by LDO motors. These are great motors, and include Voron branding.
Add to cart Details Buy Now

Quick View

Voron V2.4 Motor Kit by LKD
Original price was: $189.90.Current price is: $149.90.

This is a complete motor set for the Voron 2.4 by LKD. These are great motors without expensive branding.
Add to cart Details Buy Now

Quick View

Voron V2.4 R2 300mm Kit (LDO, NO PI)
$1,699.00

Voron 2.4 Corexy V2.4 R2 Version 3D Printer Kit with High Quality Parts 300*300mm DIY Kit
Add to cart Details Buy Now

Brendan

5

13 March 2024 - Revi... Read More

13 March 2024 - Review for: PETG-CF – Carbon Fibre Enhanced PETG Filament Interesting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan. I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove! Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use. My suggestion - get PETG printing well, before moving onto this filament. My printing factors currently: Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/s REVIEW FOR ASA Blue-Grey Printed the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield. Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layers Note: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube. My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel. You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts. Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish. Next step is try printing in an enclosure and to try Acetone smoothing :) NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less
Greedo Twerp

5

I was looking for a ... Read More

I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less
GLEN20

5

3dea is a real pleas... Read More

3dea is a real pleasure to deal with. Not only do they stock a great range of filament which you can get from other suppliers in NZ. They have a massive range of own-brand filament which is often unique to NZ and is of the highest quality. All in all, 3dea are highly recommended. Read Less

Write a review!

Category: 3D Printer Kits

FYSETC Stealthburner PCB Kit with Cables for Voron 2.4 / R2 / Trident (2pcs version)

LDO Galileo 2 Kit for Clockwork 2 (G2E)

LDO Input Shaper Toolkit

LDO Leviathan V1.2 Control Board

LDO NiteHawk SB Toolboard Kit Rev. C

LDO NiteHawk-36 Toolboard REV C

LDO V1 Z Motor Triple (V1ZMKT3) Teflon Coated for Trident

PrusaClone i3 MK3S Bear 2.1 Printer Kit

Quality StealthBurner Extruder Screw Fastener Fans Kit / Voron 2.4 / Trident

Voron Printed Parts Kits

Voron V2.4 Motor Kit by LDO Motors (Clockwork 2 updated)

Voron V2.4 Motor Kit by LKD

Voron V2.4 R2 300mm Kit (LDO, NO PI)

FREE SHIPPING for AKL @ $180 | NI @ $300 | SI @ $360

© 2024 FISAG Ltd – 3DEA