10 rolls mixed colour.

Most colours are limited to two per pack – black, white, silver and some other common colours are limited to 5.
For the 2.85mm dimension all products are limited to two per colour.

eSUN PLA+ 3D Printer Filaments are a popular choice with a lot of good user feedback. It is tougher than regular PLA.

ADVANTAGES:
– suitable for printing larger models
– toughness is higher than regular PLA
– less stringing, the surface of the printouts will be smoother and more delicate
– no cracking problem
– FDA food safe approved

PLA + Printing Parameters:
Best print temperature: 205-225 °C
Base temperature: 0/65 °C
Feed speed: 30-90mm / s
Idling speed: 90-150mm/s

Filament diameter:1.75mm:±0.02mm
Certification: ROHS Certified, REACH
Materials: Polylactic acid plus (PLA+)

Brand	eSun

eSun Olive Green PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Olive Green

eSun White PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	White

eSun Cold White PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Cold White

eSun Blue PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Blue

eSun Red PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Red

eSun Orange PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Orange

eSun Silver PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Silver

eSun Grey PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Grey

eSun Light Blue PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Light Blue

eSun Magenta PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Magenta

eSun Bone White PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Bone White

eSun Dark Blue PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Dark Blue

eSun Black PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Black

eSun Yellow PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Yellow

eSun Green PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Green

eSun Pink PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Pink

eSun Peak Green PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Peak Green

eSun Purple PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Purple

eSun Gold PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Gold

eSun Pine Green PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Pine Green

eSun Beige PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Beige

eSun Brown PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Brown

eSun Light Brown PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Light Brown

eSun Fire Engine Red PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Fire Engine Red

eSun Space Blue PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Space Blue

eSun Very Peri PLA+ 1.75mm

Weight	1 kg
Brand	eSun
Colour	Very Peri

Reviews

There are no reviews yet.

Be the first to review “eSun PLA+ 10x 1Kg – Mixed”

GLEN20

5

3dea is a real pleas... Read More
3dea is a real pleasure to deal with. Not only do they stock a great range of filament which you can get from other suppliers in NZ. They have a massive range of own-brand filament which is often unique to NZ and is of the highest quality. All in all, 3dea are highly recommended. Read Less
Brendan

5

13 March 2024 - Revi... Read More
13 March 2024 - Review for:PETG-CF – Carbon Fibre Enhanced PETG FilamentInteresting combination of materials. Has the stiffness of ASA but the toughness of PETG. Also like ASA, I found a tendency for the layers to separate if printed with the same temp as PETG. Raising the extruder temperature helped, but then I found blobs forming. A good balance seems to be 242degC with a touch of fan.I'm printing on a Garolite print bed and found I had to bring the bed temp down to 70degC, any hotter and the print is very hard to remove!Also, remember you'll need a steel nozzle, as apparently the CF will ream out your orifice quick smart. The filament is hygroscopic so needs to be dried before use.My suggestion - get PETG printing well, before moving onto this filament.My printing factors currently:Ender3 v2 with MicroSwiss DD Extruder 0.6mm hardened steel MicroSwiss Nozzle Retraction: 1.5mm Garolite Printbed Extruder Temp: 242degC Fan: 5% always on | Bridges: 40% Layer Height: .24mm Perim: 35mm/s Small Perim: 25 mm/s Ext PErim: 20 mm/sREVIEW FOR ASA Blue-GreyPrinted the three parts in the photo attached, individually on an Ender 3 v2 without an enclosure, but with a printed draft shield.Nozzle at 250 degC first layer, then 246 degC for the following layers Bed at 102 degC first layer, then 98 degC for the following layersNote: I have a Capricorn PTFE Bowden Tube. Better temp durability than E3v2 stock Bowden tube.My bed plate is Garolite wet sanded with 1200 grit wet n dry and cleaned between prints with Isopropyl and paper towel.You don't want to be in the same room as the printer when printing ASA - smells bad. Also, once the first layer has finished, keep the door closed to avoid drafts.Print rough smoothed using 240 grit sandpaper, then 1200 wet n dry - wet sanded. ASA sands easily and down to a great finish.Next step is try printing in an enclosure and to try Acetone smoothing :)NOTE: The supplied filament reel's centre-hole is too small for my Ender 3 v2 reel holder. I use a dryer so all good, would be frustrating if you wanted to use a stock holder. EDIT: Must have had my eyes closed - The spool holes have filler plates! Removing these plates and my conundrum was solved :) Read Less
Greedo Twerp

5

I was looking for a ... Read More
I was looking for a colour similar to the primer red seen on German WW2 heavy vehicles. Wanted to print a 1/4 scale model of a Tiger tank 88mm muzzle brake. Ordered the 3DEA "Brick Red" PLA which is a very good match. Never used prior and pleased to report printed faultlessly once I knocked the temp down to 200 degrees on my Kingroon KP3S. Printed at 0.10mm layer height, no stringing issues at all. Very happy customer. Already planning the next order, highly recommended. Read Less

Write a review!